Airpress 18003-OFAG3 Adsorption dryer set ISO OFAG3 180 l/min Class Zero

Airpress Adsorption dryer set ISO OFAG3 180 l/min Class Zero

Features

• Clean compressed air is important in compressed air installation.
• A continuous process through a reliable compressed air supply is a proven fact. The OFAG3 is designed for all applications where compressed air is required according to the ISO8573-1 standard.
• A big plus to the OFAG3 adsorption dryers is the coating on the inside of the filter pots, which makes the reaction of ammonia with condensation and aluminum of the housing a thing of the past.
• This prevents blockages and malfunctions in the adsorption dryer system.
• The adsorption dryer has a continuous pressure dew point of at least -20°C and a maximum of -70°C.
• This removes 99.99% of the moisture from the air.
• The adsorption dryer is further equipped with silencers, visible pressure gauges and the fittings are made of stainless steel for increased strength and better air passage.
• To purify the compressed air, five filters complying with the ISO8573-1:1.3.1/0 standard are used.
• In front of the dryer are the pre-filters: cyclone filter, P filter and an S filter.
• The cyclone filter filters water from the compressed air.
• The rotary motion of the compressed air forces the condensate against the housing, causing the water to sink to the bottom of the filter jar.
• The air rises again and is 98% free of condensation.
• The P filter is a coarse filter that purifies solids and more water.
• The S filter is a superfine filter for solids and oil residues down to 0.01 microns, providing pure compressed air.
• After the dryer, there are after-filters, namely an R filter and an A2 filter.
• The R filter is a dust filter to stop any adsorbent that may come along from the columns.
• The A2 filter is the final filter that removes oil vapors to a residual of 0.005-0.001 mg/m3 through a cassette filled with activated carbon.
• An automatic drain with float function is installed to remove the condensation water from the cyclone filter pot.
• The P filter has an electronically controlled drain which is controlled by the timer function in the dryer's controller.
• In fact, the timer function is built into the dryer's controller.
• You need to connect the wiring to the controller's circuit board.
• The adsorption dryer set is suitable for companies where clean compressed air is a requirement.
• On dairy farms, for example, it is important to provide barn pneumatics with very clean compressed air.
• This virtually eliminates the chance of malfunctions and damage to pneumatic components, due to any contaminated compressed air.
• Clean compressed air is also very important in companies such as the packaging industry, auto garages, workshops, gardeners and, for example, the pharmaceutical industry.

Technical data

• Weight (kg) 13.50
• Dimensions (mm) 480 x 130 x 710
• Connection size (3/8, 1/2
• Nominal value air supply (Nm3/h) 10.8
• Nominal value air supply (l/min) 180
• Rated value air output (Nm3/h) 10.80
• Rated air output (l/min) 180
• Pre-filter (type) P-filter - 3 µm, Cyclone filter, S-filter - 0.01 µm
• Afterfilter (type) A2 - 0.005 mg/m3, R-filter - 1 µm
• Residual oil content (mg/m3) <0.005
• Pressure dew point (°C) -20 / -25
• Working pressure (bar) 4 - 16
• Minimum ambient temperature (°C) 1.5
• Maximum ambient temperature (°C) 60
• Voltage (V) 230 V / 50 Hz / 1 Ph
• Power consumption (w) <40
• IP class IP 65
• Noise level dB(A) (0 m) <100
• ISO ISO8573-1, ISO8573-1:1.3.1 / 0
• Distance sensor No.

Scope of delivery

• Manual