TEC7 TEC7PURTN TEC-7 PUR starter kit 5 pieces

TEC7 TEC7PURTN TEC-7 PUR starter kit 5 pieces

GT7 features

• GT7 is a true TEC7 product
• One product, many applications? Check it out!
• Innovatief? Check!
• Very high quality? Check!
• GT7 is a very versatile spray which frees up a lot of space in your warehouse shelves: deep penetration moisture repellent powerful rust preventer penetrating oil: loosens what is stuck high quality lubricant contact spray: perfect electrical contacts cleaner protection of all surfaces

Specifications GT7

• Kookpunt: 187°C - 211°C
• Vapour pressure at 20°C, Pa: 100
• Relative density at 20°C: 0.808
• Physical state at 20°C: liquid
• Vlampunt: 67°C
• Auto-ignition: 255°C
• Water solubility: insoluble
• Dynamic viscosity at 20°C: 1 mPa.s
• Kinematic viscosity at 20°C: 1 mPa.s
• Protective period: 8-12 months, the duration of the protection can be extended by regularly applying GT7
• Outdoors, this protection time may change depending on weather conditions
• Shelf life: 3 years

Features Super7

• SUPER7 is much more than ''just'' a rock-solid instant glue
• It is a highly fluid and crystal-clear adhesive with a very wide range of uses. repair paste with sand or sawdust as filler iron-strong adhesive for very thin layers transparent all-purpose adhesive use in combination with SUPER7 Activator for porous surfaces the activator accelerates the curing, also on smooth surfaces

Specifications SUPER7

• Before: druppelflacon
• Basis: cyanoacrylaat
• Colour: colourless, transparent
• Viscosity: very low, thin
• Specific gravity: 1.05 - 1.09 kg/m³
• Vlampunt: 87°C
• Consumption: 1 drop ≈ 0,02g ≈ 3 to 5 cm² adhesive surface
• Adherence: very good on most materials not: Polypropylene (PP), Polyethylene (PE), Teflon® (PTFE) and other technical plastics can give adhesion problems
• After curing: Temperature resistance: permanent: - 30°C / 80°C peak: 100°C over 200°C to 250°C release bonding good resistance to temperature fluctuations and weather influences
• Chemical resistance: resistant to many solvents, oil, benzene, many chemicals not resistant to strong solvents and strong alkalis. slowly soluble in: dimethylformamide, ethyl acetate, acetone, methylene chloride
• Electrical resistance: insulator volume resistance DIN 53482* = >1015 Ohm.cm dielectric strength DIN 53481* = 11-13 kV/mm * = measured on adhesive bonded joints
• Adhesive thickness: max. 0.8 mm when used with activator max. 0.2 mm without activator thinner layers give a stronger bond
• Shrinkage: none at the prescribed layer thicknesses

Specifications SUPER7Activator

• Form: aerosol
• Base: polymerization-catalyst in solvent
• Colour: light amber to colourless
• Viscosity: very low, thin liquid
• Specific weight: approx. 0.6 kg/dm³
• Flash point: slightly inflammable
• Consumption: depending on the porosity of the substrate and the application technique. With 1 aerosol can (150 ml) hundreds of bondings are possible

Features Magic Clean

• clean and degrease: hands, tools, engines, boats, motorcycles, ... Effective against ink, printing inks, markers, oils, greases, nicotine, graffiti, ... Removal of non-cured synthetic resins, MS-polymers, silicones, PUR-foam, ... Fresh perfume and skin-friendly composition, due to glycerine

Specifications for Magic Clean

• Wipes: strong polycotton fabric
• Cleaners: ethyl alcohol, dimethyl glutarde, dimethyl succinde
• Fragrance: added perfume
• Skin protector: glycerin
• Shelf life: 12 months

Features Pur 7 Gun

• Foam guns exist in many qualities
• TEC7 only chooses the best quality
• So you can be sure that your gun is always ready, without leak